\uf0a7Finally, steam to\u00a0 the coat should shut off, the unloading door is to be opened <\/p>\n
\uf0a7Then the shaft and mixing arms are reversed to behave as unloading mechanism and should scoop the waste fragments out of <\/p>\n
the unloading door, onto a conveyor belt or directly into a waste container. <\/p>\n
\uf0a7The vessel should now be ready for another treatment cycle, having retained most of its heat to the treatment of the <\/p>\n
next batch. <\/p>\n
(B)Features and Specification of the Steam Boiler: <\/p>\n
Features of the Boiler: <\/p>\n
\uf0a7It must be an Electrical boiler <\/p>\n
\uf0a7Splash proof electric enclosure and switches <\/p>\n
\uf0a7Door Isolator to main electric enclosure <\/p>\n
\uf0a7Alarm lights and Safety\/protection against excel pressure <\/p>\n
\uf0a7Level control on feedback water tank <\/p>\n
Technical specification of the Boiler: <\/p>\n
\uf0a7Output: between: 90-110 kg\/h (F&A 100 deg C) <\/p>\n
\uf0a7Working pressure: between 7-10 bar <\/p>\n
\uf0a7Boiler water content: between 80-100 liter <\/p>\n
\uf0a7Feed water tank material: between 60-80 liter <\/p>\n
\uf0a7Power consumption: between 60-75 Kw <\/p>\n
\uf0a7Number of Heating Elements: 3-4 nos. <\/p>\n
\uf0a7Electrical requirements: 400Vac, 50 Hz, 3 ph <\/p>\n
(C)Technical Specifications of Tub washer <\/p>\n
Features: <\/p>\n
\uf0a7Fully automatic and manual modes. <\/p>\n
\uf0a7metallic construction, SA 240\/304 <\/p>\n
\uf0a7Sensors to maximize both system efficiency and operator safety. <\/p>\n
\uf0a7Must use Re-circulating cold wash water to minimize water consumption and operating costs <\/p>\n
\uf0a7Disinfects all bin surfaces <\/p>\n
\uf0a7Software Strong blow dryer to remove excess surface water <\/p>\n
\uf0a7has to be compliant with North American and EU regulations <\/p>\n
Specifications: <\/p>\n
\uf0a7Tub washer able to wash bins of a suitable size, the norm being 38 gram <\/p>\n
\uf0a7has to have an water reservoir of capacity minimum: 225 liter <\/p>\n
\uf0a7Perfectly suited to hospitals and clinics by processing up to min.300 bins per hour. <\/p>\n
\uf0a7Time to wash and dry one bin after loading-approximately 12 nos. <\/p>\n
\uf0a7Bins loading on wash station at a time -approximately 12 nos. <\/p>\n
\uf0a7Total length: approx 30.0 ft <\/p>\n
\uf0a7Total length: approx 8.0 ft <\/p>\n
\uf0a7Total length: approx 3.0-3.5 ft <\/p>\n
\uf0a7Height to Conveyer from floor: approx 3 feet. <\/p>\n
Drive of the Tub washer <\/p>\n
\uf0a7Motor driven <\/p>\n
\uf0a7Motor Horsepower: approx. 4.0 HP <\/p>\n
\uf0a7Power: 220vac, 1 ph or 400 VAC, 3 ph or to suit customer needs <\/p>\n
Bins to be included <\/p>\n
\uf0a7200 nos. With different color (depending on the actual requirement of the hospital) <\/p>\n
(D)Technical Specification of External SHREDDER Controls <\/p>\n
\uf0a7Pre-programmed PLC controlled <\/p>\n
\uf0a7Password activated and reversal history indication <\/p>\n
\uf0a7Motor starter with overload protection <\/p>\n
\uf0a7Automatic instantaneous stop on hard thing in shredder mattress <\/p>\n
\uf0a7Automatic heavy cutting load reversal and re-try , up to three times <\/p>\n
\uf0a7Control housing Nema Type 12 <\/p>\n
Cutting Hardwires <\/p>\n
\uf0a7Chamber Dimensions (W x L x H): approx. 33 cm x 38 cm x 25 cm <\/p>\n
\uf0a7Number of Knives: approx 18 or to match customer needs <\/p>\n
\uf0a7Knife Thickness: approx 18 mm or to suit customer needs <\/p>\n
\uf0a7Knife Diameter: approx 16 cm or to suit client needs <\/p>\n
\uf0a7Teeth per Knife: minimum 3 <\/p>\n
\uf0a7Number of Shafts: 2 ie double rotating shredder <\/p>\n
Drive of the shredder <\/p>\n
\uf0a7has to be motor driven <\/p>\n
\uf0a7Motor Horsepower: approx. 10 HP <\/p>\n
\uf0a7Motor RPM: minimum 1750 <\/p>\n
\uf0a7Speed Reduction: 60:1 <\/p>\n
\uf0a7Generated Torque: min 40 Nm or 350 Ibs\/in. <\/p>\n
\uf0a7Gearbox: should be Parallel shaft <\/p>\n
\uf0a7Shock Protection: Rubber Mount Torque Arm <\/p>\n
\uf0a7Power: 220vac, 1 ph\u00a0 or 400 VAC, Ph or to suit customer needs <\/p>\n
Ancillaries to be included <\/p>\n
\uf0a7Shredder stand, fabricated from 3″ sq. steel tubing, regular height 30 inches <\/p>\n
\uf0a7Shredder hopper, fabricated from 16 gauge steel, with optional switched hopper lid <\/p>\n
(E)Features & Technical Specification of Conveyer <\/p>\n
To carry processed waste from vessel to shredder <\/p>\n
Controls <\/p>\n
\uf0a7Motor starter with overload protection <\/p>\n
\uf0a7Control housing Nema Type 12 <\/p>\n
\uf0a7Safety pull-stops along either side of conveyer <\/p>\n
Ancillaries <\/p>\n
\uf0a7Conveyer stand, fabricated from 2″ sq. steel\u00a0 tube <\/p>\n
\uf0a7Raised sidewalls fabricated from 16 gauge steel <\/p>\n
Dimensions <\/p>\n
\uf0a7Over-all length: between 20-25 ft or proper length based on the setup requirement. <\/p>\n
\uf0a7Over-all width: between 24-30 inch <\/p>\n
\uf0a7Over-all height (without including stand): between 12-14 inch <\/p>\n
\uf0a7Available inclines:\u00a0\u00a0\u00a0 0-40 degrees <\/p>\n
\uf0a7Belt Speed: 75 ft\/min <\/p>\n
\uf0a7Dam spacing: approx. 16 inch <\/p>\n
Drive <\/p>\n
\uf0a7Motor driven <\/p>\n
\uf0a7Horsepower:approx. 0.75 HP <\/p>\n
\uf0a7Motor RPM: approx. 60 <\/p>\n
\uf0a7Electrical Power input: 220vac, 1phj or 400 VAC, 3 Ph or to suit customer needs <\/p>\n
(F)Technical Specification of Tipper <\/p>\n
Features: <\/p>\n
\uf0a7It is to be made to allow for effortless bin positioning beneath the door to unload processed waste and effortless <\/p>\n
maneuverability for lifting and tipping the waste to the shredder hopper. <\/p>\n
\uf0a7Equipped with 2 binds to adapt processed waste loads to be loaded to the shredder and shredder waste to be <\/p>\n
transported to the disposal bin. <\/p>\n
\uf0a7Frame: Rugged heavy duty frame constructed of formed and welded steel for extra strength <\/p>\n
\uf0a7Mast: Fabricated using cannel steel for greater strength and dependability. Open structure design complete with security <\/p>\n
cage to offer greater visibility. <\/p>\n","protected":false},"excerpt":{"rendered":"
\uf0a7Finally, steam to\u00a0 the coat should shut off, the unloading door is to be opened \uf0a7Then the shaft and mixing arms are reversed to behave as unloading mechanism […]<\/p>\n","protected":false},"author":1,"featured_media":2005,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[1],"tags":[],"_links":{"self":[{"href":"https:\/\/gofullday.com\/incineration\/wp-json\/wp\/v2\/posts\/3796"}],"collection":[{"href":"https:\/\/gofullday.com\/incineration\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/gofullday.com\/incineration\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/gofullday.com\/incineration\/wp-json\/wp\/v2\/users\/1"}],"replies":[{"embeddable":true,"href":"https:\/\/gofullday.com\/incineration\/wp-json\/wp\/v2\/comments?post=3796"}],"version-history":[{"count":1,"href":"https:\/\/gofullday.com\/incineration\/wp-json\/wp\/v2\/posts\/3796\/revisions"}],"predecessor-version":[{"id":9788,"href":"https:\/\/gofullday.com\/incineration\/wp-json\/wp\/v2\/posts\/3796\/revisions\/9788"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/gofullday.com\/incineration\/wp-json\/wp\/v2\/media\/2005"}],"wp:attachment":[{"href":"https:\/\/gofullday.com\/incineration\/wp-json\/wp\/v2\/media?parent=3796"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/gofullday.com\/incineration\/wp-json\/wp\/v2\/categories?post=3796"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/gofullday.com\/incineration\/wp-json\/wp\/v2\/tags?post=3796"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}