clinical facility incinerator manufacturers – Waste Incinerators

Chamber (Afterburner Optimum departure temperature must not be much less than 1100oC

• This chamber should be equipped with burners that use low sulphur
• The chamber should ensure a minimum exit temperature of 850 degrees
• This unit should operate at over 1100 deg C to ensure complete
• This chamber should be equipped with burners that use low sulphur
• Heavy-duty steel casing
• High quality refractory lining and insulation
• Large full size top load door and liquid retention
• 1 x oil fired ignition burners operated on/off

• Secondary Combustion Chamber (After burner)

1. Heavy-duty steel casing
2. High quality refractory lining and insulation
3. 1 x oil burner
4. Should be fitted with burners that use low sulphur
5. Ensure secondary air supply is controlled.
6. Ensure residence time is not less than two seconds.
7. Ensure that the gas temperature as measured against the inside wall in the secondary chamber and not in the flame zone is not less than 1100 degrees
8. Ensure the emitted oxygen content of the emitted gases is not less than 11%
9. Ensure both primary and secondary combustion temperatures are maintained until all waste is completely

Security interlock, Fan Newbie, Heating System on/ off switch/door security button, Vehicle coating button, temperature levels regulate device.

1. Cyclone separator
2. Electrostatic precipitators
3. Fabric filters

1. The chimney should have a minimum height of 10 meters above ground level and clear the highest point of the building by not less than 3 meters for all The topography and height of adjacent buildings within 50 meters radius should be taken into account.
2. The chimney should be visible to the operator from the feeding

1. The minimum exit velocity should be 10 meters per second and at least twice the surrounding wind speed (Efflux velocity = wind speed x 2) whichever is higher to ensure no down washing of exiting
2. The point for measurement of emissions shall be

1. Instrument for determining the inside wall temperature and not burner flame temperature must be provided for both primary and secondary
2. An audible and visible alarm must be installed to warn the operator when the secondary chamber temperature drops to below the required
3. A carbon monoxide and oxygen meter/recorder should be
4. A smoke density meter/recorder should be
5. A solid particulate meter/recorder should be
6. Any other instrument that may be considered

• Location / Siting of the Incinerator

1. a) The incinerator must be sited in accordance with the relevant local municipal authority planning regulations and the topography of the site must be compatible with premises in the

99. Combustion efficiency (C.E) shall be at least00% where C.E = %Carbon dioxide x 100 / [% Carbon dioxide + carbon monoxide]
100. The temperature of the primary chamber shall be 800 +/- 50 degrees centigrade
101. The secondary chamber gas residence time shall be at least 1 second at 1050 +/- 50 degrees centigrade with 3% oxygen in the stack
102. Opacity of the smoke must not exceed 20% viewed from 50 metres with naked
103. All the emission to the air other than steam or water vapour must be odourless and free of mist, fume and
104. A 99.99% destruction and removal efficiency (DRE) for each principal organic hazardous constituent (POHC) in the waste feed where DRE [ ( Win – Wout) /Win ] x

Key Combustion Chamber Minimum departure temperature level need to not be much less than 850oC

1. The average dioxin and furan concentration in the emission should not exceed 80mg/m3 total dioxins and furans if measured for a period of 6 to 16

1. Auto
2. No pilots to
3. Automatic control and temperature monitoring
4. Built-in skid facilitates placement

1. Rapid incineration means low fuel

2. Up to 20kgs per hour (dependant on application).
3. Thick refractory lining rated to 1400 deg C in main chamber retains heat, increasing

1. Heat resistant 3mm
2. Stainless steel

1. Low running and maintenance costs
2. Fully Automatic and simple to operate control panel
3. Afterburner Preheat
4. Incineration Temperatures in Excess of 900 degrees C
5. 3 mm Steel Casing and Fully insulated
6. Dense Refractory Concrete Lining Rated to 1400 degrees C
7. Solid Hearth to Allow Maximum Burnout
8. Large Top Opening Lid For Easy Loading
9. Stainless Steel Flue as standard
10. 12 Months or 1000 hours
11. Optional Stainless Steel Casing
12. Heat Recovery System option

3.13	Fuel and Capacity
1.	Low sulphur fuel
2.	Capacity (Cubic Mtr)	.10
3.	Average Capacity	40kg
4.	Fuel Consumption (ltrs / hr)	3

1.	Length (mm)               735
2.	Width (mm)                500
3.	Height Incl. Flue (mm)	1960
4.	Door Opening (mm)	325 x 325

1.	Length (mm)	620
2.	Width (mm)	390
3.	Height	500

1. Minimum Operating Temperature 950
2. Maximum Operating Temperature 1320

3.	Burn rate per hour	5-20kgs
4.	Temperature Monitoring	Available

Second Burning Optimum leave temperature level need to be no lot less than 1100oC